How to install a car audio system in your home?
2022-02-04 by wlinn
If you drive frequently, you understand the importance of having a high-quality car sound system. Listening to music or a podcast when stuck in traffic, on a road trip, or commuting to work is a terrific way to pass the time. If your old car's audio system inside is in good repair, don't toss your audio system and car both in the garage. Thinking these are now useless, install a car audio system in your home; this would let you have a powerful audio system.
Contemporary factory-installed audio systems offer many more options and functions than their predecessors; they still fall short of some of the most effective automobile audio systems available. Hence, you may need to install a new audio system. The capacity to play various media formats increases power output, and docking stations are just a few capabilities.
Car audio is equipment fitted in a car or other vehicle to offer the occupants in-car entertainment and information. There are three essential components in every automotive audio system.
- The first one is radio, also known as the "head unit," which controls the entire system and creates the audio signal.
- The second element is an amplifier, which increases the power of the audio signal.
- 3rd component is speakers to reproduce the sound.
How to install a car audio system?
A sound system from car to home means changing a battery-powered audio system to an electrically powered audio system. It may appear to be a little far-fetched, but to install a car audio system in your home is, in fact, possible. Before converting the automobile audio to home audio, there are two significant chores to complete.
- To begin, remove the complete audio unit from the vehicle.
- The second stage configures the system to work with your home's electrical system.
Let's discuss the steps of removing the audio from the car before you start a step-by-step method to install a car audio system in your home. However, the unmounting process may differ depending on the car model and how the system was fitted. Initially, you need to remove the audio system from the car.
Disconnect the battery- Using a tool, loosen the clamp bolts connecting the power wires and the battery.
Panel removal- Using a trim stick, remove the boards surrounding the system.
Then, remove all of the screws holding the car's trim board in place and lift it off. It's best to use a hooked tool for the manual window.
Following are the steps required for installing an audio system at home.
Step no. 1
Gather the necessary materials.
- Speakers for the car audio system
- Even if it is old but working, a computer power supply unit (PSU)
- PSU installation boxes (homemade is still okay)
- crimps and wire strippers
Step no. 2
The second step is to connect the power supply unit to the rest of the system.
Get the giant connector on the PSU that has a lot of various colored wires, but you need the green one and the black one next to it for your case. Cut a piece of wire, strip both ends, and attach one end to the pin linked to the green wire and the other to the black wire. It acts as a jump starter and powers up the PSU when you turn it on.
Caution: Don't plug the power supply unit into any outlet during this procedure.
Step no. 3
The third step is to connect the various components of the system.
Next, take the yellow and red wires from the automobile audio system, strip them, and connect them to the yellow wire on the PSU. Get the black ground wire from the system, pull it out, and connect it to another black on the PSU (different from the first one related to green via a small piece that you cut). At this point, you can turn on the power supply unit to see if it turns on, then unplug it to proceed.
Step no. 4
Now you will connect the system and the power supply unit
Connect the wires to the pin connectors; the black ground wire from the automobile system goes to the connector's black wire, while the red and yellow wires from the audio system both go to the connector's yellow wire. Yellow indicates continuous, black is ground, and red is ignition, as you may recall from your stereo.
Step no. 5
In this step, you need to install the Sound System.
The size of your head unit determines the number of speakers you can connect. The process of connecting speakers is as straightforward as it appears. If you desire to surround sound, you can have front and rear speakers. A positive wire can be any color, while a negative cable has a black stripe running vertically from top to bottom.
Step no. 6
Now measure the box and assemble the units. Take the measures of the system, and then cut the box to fit its measurements and the PSU. Measure and cut a hole for the power supply unit socket and the speakers in the box.
Step no. 7
Connect the power inverter to a wall outlet and turn it on. After that, put everything in its proper box according to the measurements and, if necessary, secure it with screws.
If you correctly follow all of the procedures above, you should now be able to use your charged battery car audio system with electricity from your home's wall outlet.
Read more: How to connect android music to car radio?
Conclusion
We concluded that you might easily install a car audio system in your home without the help of professionals. Following these steps, you can install the audio system in your car without spending money.
